If you’re trying to connect to your Rockspace Wi-Fi extender but notice that Rockspace_EXT not showing in your list of available networks, don’t worry—this is a common issue with simple solutions. Whether you’re setting up your extender for the first time or reconnecting after a power outage, this guide will walk you through the steps to get your Rockspace extender back online.

Why Is Rockspace_EXT Not Showing Up?

The Rockspace_EXT network is the default Wi-Fi name (SSID) for Rockspace extenders. If it’s not appearing in your network list, it could be due to:

• The extender not being powered on or properly connected.
• The extender being too far from your router.
• Interference from other devices or physical obstructions.
• A temporary glitch or configuration error.

Let’s dive into the steps to resolve this issue and get your extender working again.

Step-by-Step Solutions to Fix Rockspace_EXT Not Showing

1. Check the Extender’s Power and LED Lights

• Ensure the Rockspace extender is plugged into a working power outlet.
• Look at the LED lights on the extender:
  • A solid or blinking light means the device is powered on.
  • If there are no lights, try a different outlet or check the power adapter.

2. Restart the Extender

• Unplug the extender from the power outlet.
• Wait for 30 seconds, then plug it back in.
• Allow the extender to reboot and check if Rockspace_EXT appears in your network list.

3. Reset the Extender to Factory Settings

If restarting doesn’t work, a factory reset can help:

1. Locate the reset button (usually a small pinhole on the extender).
2. Use a paperclip or pin to press and hold the button for 10–15 seconds.
3. Release the button and wait for the extender to reboot.
4. After the reset, the Rockspace_EXT network should reappear in your Wi-Fi list.

4. Move the Extender Closer to Your Router

• If the extender is too far from your router, it may not broadcast the Rockspace_EXT network effectively.
• Move the extender closer to your router and check if the network appears.

5. Reduce Interference

• Other electronic devices (e.g., microwaves, cordless phones) or physical obstructions (e.g., walls, furniture) can interfere with the extender’s signal.
• Place the extender in an open area, away from potential sources of interference.

6. Refresh Your Device’s Wi-Fi Settings

• Ensure your device’s Wi-Fi is turned on and not in airplane mode.
• Refresh the list of available networks on your device.
• If you’re using a laptop, try disabling and re-enabling the Wi-Fi adapter.

7. Use WPS to Reconnect

If the Rockspace_EXT network is still not showing up, try using the WPS (Wi-Fi Protected Setup) method:

1. Press the WPS button on your router.
2. Within 2 minutes, press the WPS button on your Rockspace extender.
3. Wait for the extender to connect to your router. The Rockspace_EXT network should reappear.

8. Manually Connect to the Extender

If the network is still not visible, try connecting manually:

1. Look for the extender’s default network name (e.g., Rockspace_XXXX) in your Wi-Fi list.
2. Connect to this network using the default password (found on the extender’s label or in the user manual).
3. Access the extender’s setup page via a web browser (e.g., http://re.rockspace.local or 192.168.0.254) and reconfigure it.

9. Update the Extender’s Firmware

• Outdated firmware can cause connectivity issues.
• Visit the Rockspace support website, download the latest firmware for your extender model, and follow the instructions to update it.

FAQ

The post Troubleshooting Guide: How to Resolve rockspace_EXT Not showing in Your Network List appeared first on Re.Rockspace.local.

If you’re experiencing connectivity issues with your Rockspace AC1200 Wi-Fi extender or simply want to restore it to its factory settings, performing a reset is the solution. Resetting your extender can help resolve technical glitches, forgotten passwords, or configuration errors. In this guide, we’ll walk you through the simple steps to reset your Rockspace AC1200 Wi-Fi extender and get it back up and running smoothly.

Why Reset Your Rockspace AC1200 Wi-Fi Extender?

The Rockspace AC1200 extender is a reliable device designed to boost your internet coverage. However, like any tech gadget, it may occasionally encounter issues such as:

• Difficulty connecting to your router.
• Forgotten login credentials.
• Poor performance or slow speeds.
• Configuration errors during setup.

A reset restores the extender to its original factory settings, allowing you to start fresh and reconfigure it for optimal performance.

How to Reset Your Rockspace AC1200 Wi-Fi Extender

Resetting your Rockspace AC1200 Wi-Fi extender is a quick and straightforward process. Follow these steps to get it done:

Step 1: Locate the Reset Button

The reset button on the Rockspace AC1200 is typically a small pinhole located on the side or bottom of the device. You’ll need a paperclip, pin, or similar tool to press it.

Step 2: Power On the Extender

Ensure your extender is plugged into a power outlet and turned on. The LED lights should be visible, indicating that the device is powered up.

Step 3: Press and Hold the Reset Button

Using your paperclip or pin, press and hold the reset button for 10–15 seconds. You’ll notice the LED lights blinking or changing color, signaling that the reset process has started.

Step 4: Wait for the Reset to Complete

After releasing the button, the extender will reboot and restore its factory settings. This process may take a few minutes. Once completed, all previous configurations, including Wi-Fi network names and passwords, will be erased.

What to Do After Resetting Your Rockspace AC1200 Extender

Once the reset is complete, you’ll need to reconfigure your extender to connect it to your Wi-Fi network. Here’s how:

Connect to the Extender’s Default Network:

• On your smartphone, tablet, or computer, go to the Wi-Fi settings.
• Look for the default network name (e.g., “Rockspace_XXXX”) and connect to it. The default password is usually printed on the extender’s label or in the user manual.

Access the Setup Page:

• Open a web browser and enter the extender’s default IP address (e.g., http://re.rockspace.local or 192.168.0.254).
• Follow the on-screen instructions to set up your extender.

Reconnect Your Devices:

After reconfiguring the extender, reconnect your devices to the extended Wi-Fi network.

Troubleshooting Tips for Rockspace AC1200 Wi-Fi Extender Reset

• Reset Button Not Working: Ensure you’re holding the button for the full 10–15 seconds. If it still doesn’t work, unplug the extender, wait 30 seconds, and try again.
• No LED Indicators: Check that the extender is properly plugged into a power outlet.
• Forgotten Default Password: Refer to the label on the extender or the user manual for the default credentials.

By following this guide, you’ll have no trouble performing a Rockspace AC1200 Wi-Fi extender reset and ensuring your device works like new.

The post Guide to Rockspace AC1200 Wi-Fi Extender Reset: Easy Steps for USA Users appeared first on Re.Rockspace.local.

If you’re looking to boost your outdoor Wi-Fi coverage while adding smart control to outdoor devices, the ROCK PE1 2-in-1 Outdoor Smart Plug and Wi-Fi Range Extender is an ideal solution. This setup guide will walk you through the easy steps to get your ROCK PE1 up and running without hassle. Let’s get started!

What is the ROCK PE1 Outdoor Smart Plug and Wi-Fi Extender?

The ROCK PE1 is a dual-purpose device that combines a smart outdoor plug and a Wi-Fi extender. It provides remote control over outdoor devices and expands Wi-Fi coverage for your backyard, garden, or patio. Imagine controlling garden lights or sprinklers from your smartphone while also enjoying seamless internet connectivity outdoors – that’s the convenience ROCK PE1 offers.

Key Benefits of the ROCK PE1

1. Remote Device Control: Easily control any device plugged into your ROCK PE1 from anywhere using your smartphone.
2. Extended Wi-Fi Coverage: ROCK PE1 acts as a Wi-Fi extender to eliminate dead zones around your property, ensuring consistent connectivity.
3. Weather-Resistant Design: Built to withstand outdoor conditions, ROCK PE1 is perfect for all-weather use.

Now, let’s dive into the setup process.

Step-by-Step Guide to Setup ROCK PE1

Step 1: Choose an Optimal Location

To get the best Wi-Fi coverage, plug your ROCK PE1 into an outdoor outlet roughly halfway between your router and the area where you need coverage. Ensure it’s within range of your Wi-Fi router.

Step 2: Power On the Device

Plug the ROCK PE1 into the power outlet and wait for the LED indicator to turn green. This indicates that the device is powered on and ready for setup.

Step 3: Connect to the ROCK PE1’s Network

• On your smartphone or computer, open the list of available Wi-Fi networks.
• Find and connect to the network named “rockspace_EXT”.
  • Note: For computers, ensure you’re disconnected from any Ethernet cable. For smartphones, turn off mobile data to avoid interference.

Step 4: Access the Web-Based Setup Page

• Once connected to the “rockspace_EXT” network, a login page may appear automatically.
• If it doesn’t, open a web browser and type http://wifi.rockspacewifi.com or http://192.168.0.254 in the address bar to access the setup page.

Step 5: Create an Admin Password

On the setup page, you’ll be prompted to create a password for managing the ROCK PE1. Choose a secure password and save it for future access.

Step 6: Select Your Wi-Fi Network to Extend

After creating the password, you’ll see a list of available Wi-Fi networks. Select your home Wi-Fi network (SSID) that you want to extend to your outdoor space.

Step 7: Enter Your Wi-Fi Password

Enter your home Wi-Fi password to allow ROCK PE1 to connect to your existing network. Wait for the page to confirm the successful connection.

Step 8: Position the ROCK PE1 for Optimal Coverage (If Needed)

After setup, you may want to relocate the ROCK PE1 to a spot with better coverage. Plug it into an outlet around halfway between your router and the area you want to cover. Wait for the Signal LED to turn blue, indicating a stable connection. If it remains another color, try moving the device closer to your router.

Troubleshooting Tips

If you run into issues, here are some troubleshooting steps:

• Reposition the Device: Make sure the ROCK PE1 is within range of your router. If necessary, plug it into an outlet closer to the router.
• Firmware Updates: Log into the management page periodically (http://wifi.rockspacewifi.com) to check for firmware updates.
• Reconnect Devices: Ensure that your outdoor devices are connected to the extended network for optimal performance.

The post How to Setup ROCK PE1: Your 2-in-1 Outdoor Smart Plug and Wi-Fi Range Extender appeared first on Re.Rockspace.local.

In today’s fast-paced digital world, a reliable internet connection is essential. But what happens when certain areas of your home or office don’t get a strong WiFi signal? That’s where the Macard N300 WiFi Extender can help. This nifty device boosts your internet coverage, so you get strong, consistent signals in every corner of your space. If you’ve recently purchased the Macard N300 extender, here’s a straightforward guide on how to set it up for the best performance.

What is the Macard N300 WiFi Extender?

The Macard N300 WiFi Extender is a compact, plug-in device designed to enhance your existing WiFi coverage. By amplifying your current WiFi signals, it helps eliminate dead zones, so you can enjoy seamless internet in areas where the connection used to be weak or non-existent.

With speeds up to 300 Mbps, it’s ideal for general internet use like browsing, video streaming, and light gaming. Now, let’s dive into the setup process!

Steps to Set Up Your Macard N300 Extender

Here’s a step-by-step guide to set up your Macard N300 WiFi Extender easily and quickly.

1. Plug in the Extender

Find a power outlet within the range of your router and plug in your Macard N300 extender. For the best performance, place it somewhere halfway between your router and the area where you want to improve WiFi coverage.

Tip: Avoid plugging the extender into an outlet behind large furniture or close to metal objects, as these can interfere with the WiFi signal.

2. Connect to the Extender Network

Once your extender is plugged in, wait for the power LED to turn solid green, which indicates it’s powered on and ready for setup.

1. Go to WiFi Settings: Open the WiFi settings on your smartphone, tablet, or computer.
2. Select the Macard Network: Look for a network named something like “Macard_N300” in the available networks list and connect to it.

3. Open the Setup Page

1. Open a Browser: Once you’re connected to the extender’s WiFi network, open a web browser (Chrome, Safari, Firefox, etc.).
2. Enter the IP Address: In the address bar, type in “192.168.10.1” and hit Enter. This should take you to the Macard N300 setup page.

4. Log In to the Setup Page

You’ll be prompted to log in to the setup page. The default credentials are usually:

• Username: admin
• Password: admin

Enter these and click on Login to proceed.

5. Select Your Home Network

After logging in, you’ll see a list of nearby WiFi networks.

1. Choose Your Network: Find and select your main WiFi network from the list.
2. Enter the Password: Type in your main WiFi password when prompted.

6. Configure the Extender

Once you’ve connected the Macard N300 to your main network, it will take a few seconds to configure the connection. The extender will automatically create an extended network, which will usually have the same name as your main network with a “_EXT” suffix.

For example, if your WiFi network is “HomeNetwork,” the extended network might be named “HomeNetwork_EXT.”

7. Connect Your Devices to the Extended Network

Once the setup is complete, disconnect from the original “Macard_N300” network and connect your devices to the extended network (“HomeNetwork_EXT”) for improved WiFi coverage.

Tips for Optimizing Your Macard N300 WiFi Extender

1. Find the Ideal Location: The placement of the extender is crucial. Ideally, it should be within range of your main router but close enough to the areas that need a stronger signal.
2. Avoid Obstacles: Large walls, metal objects, and devices like microwaves can interfere with WiFi signals. Try to keep the extender in an open space.
3. Restart Occasionally: If you notice slower speeds, restarting the extender can sometimes help refresh the connection and improve performance.

Troubleshooting Common Issues

If you’re having trouble with your Macard N300 extender setup, here are some quick solutions:

• Can’t Access the Setup Page? Ensure your device is connected to the extender’s network and try entering “192.168.10.1” again. You may also try using a different web browser.
• Forgot Password? Reset the extender by pressing the reset button (usually located on the side of the device) for about 10 seconds. This will restore the device to its factory settings, allowing you to set it up again.
• Weak Signal? Try relocating the extender closer to your main router or the desired area until you find the sweet spot for the best coverage.

Setting up the Macard N300 WiFi Extender doesn’t have to be complicated. With this simple guide, you can have your extender up and running in minutes, extending WiFi to every corner of your home. Whether you’re working, streaming, or gaming, you can now enjoy a stronger, more reliable connection.

By following these easy steps and troubleshooting tips, you’ll make the most of your Macard N300 extender setup and ensure your devices stay connected without interruptions.

Also Read- How to Setup Rockspace AC1200 extender?

The post How to Set Up Your Macard N300 WiFi Extender: A Simple Guide appeared first on Re.Rockspace.local.

Have you ever found yourself scratching your head, wondering, “I forget my Rockspace Range Extender’s Wi-Fi password, how do I recover it?” Well, you’re not alone! Losing track of your Wi-Fi password can be a real head-scratcher. But fear not, we’ve got you covered with a step-by-step guide on how to recover your Rockspace extender’s Wi-Fi password.

1. Locate Your Rockspace Extender

Before diving into the password recovery process, ensure that you can access your Rockspace extender. It should be powered on and connected to your network.

2. Connect to the Rockspace Extender

To recover your Wi-Fi password, you’ll need to connect to your Rockspace extender. Follow these steps:

1. Power On: Make sure your extender is plugged in and powered on.
2. Wi-Fi Connection: On your device, go to the Wi-Fi settings and look for the Rockspace extender’s network. Connect to it.
3. Open a Browser: Launch your web browser after connecting.

3. Access the Rockspace Extender’s Settings

Once you’re connected, open your web browser and type in the IP address 192.168.0.254 or http://re.rockspace.local for your Rockspace extender. You can usually find this information in the user manual or on the device itself.

4. Login to the Extender

You’ll need to log in to your extender’s settings. If you haven’t changed the default credentials, use the default username and password provided in the user manual or on the extender.

5. Navigate to Wi-Fi Settings

Inside the extender’s settings, find the Wi-Fi or Wireless settings section. This is where you can view or change your Wi-Fi password.

6. View Your Wi-Fi Password

In the Wi-Fi settings, look for an option that allows you to view your Wi-Fi password. It may be labeled as “Security” or “Password.” Click on it, and your Rockspace extender’s Wi-Fi password should be displayed.

7. Note Down the Password

Write down or take a screenshot of the password so you don’t forget it again. You can also change the password at this point if you wish.

Common Errors and Troubleshooting

Error 1: Can’t Access Extender’s Settings

If you can’t access the extender’s settings, ensure you’re connected to the extender’s network. Double-check the IP address you entered, and confirm your device’s connection.

Error 2: Forgot Extender Login Credentials

If you’ve forgotten your extender’s login credentials, you may need to reset the extender to its factory settings. Refer to the user manual for instructions on how to do this.

Losing your Rockspace extender’s Wi-Fi password can be frustrating, but with these simple steps, you can easily recover it. Remember to jot down your password and keep it in a safe place to avoid future hassles. If you encounter any errors or issues, refer to the troubleshooting tips provided. Now, go ahead and enjoy a seamless Wi-Fi experience with your Rockspace extender!

The post How to Recover Your Rockspace Extender’s Wi-Fi Password appeared first on Re.Rockspace.local.

In our modern world, where digital connectivity is vital, having a robust and dependable Wi-Fi connection is key to ensuring uninterrupted internet access on numerous devices. Unfortunately, Wi-Fi signals often diminish as they travel, leading to zones in your home or workplace that suffer from weak or non-existent signal. To combat this, consider using a Wi-Fi range extender. A prime example is the Rockspace AC2100 Dual-band Wi-Fi Range Extender. This device excels in broadening your Wi-Fi network’s reach, effectively banishing any dead spots and guaranteeing uniform coverage across your area.

Setting up your Rockspace AC2100 Dual-band Wi-Fi Range Extender can be a straightforward process. Here’s a step-by-step guide to help you get started:

Pre-Installation

1. Location: Before installation, find an optimal location for your extender. It should be about halfway between your router and the area with weak Wi-Fi coverage. Ensure the location is within the wireless range of your router.
2. Power Supply: Plug the extender into a power outlet. Wait for the power LED to light up. It may take a minute for the extender to boot up.

Installation Steps

Using WPS (Wi-Fi Protected Setup):

1. WPS Button on Extender: Press the WPS button on the extender for about 2 seconds. The WPS LED should start blinking.
2. WPS on Router: Within two minutes, press the WPS button on your router. The extender will automatically begin connecting to your router’s Wi-Fi network.
3. Confirmation: Once connected, the WPS LED on the extender will turn solid, indicating a successful connection.
4. Relocation: You may need to relocate the extender for optimal performance after setup. If the signal LED is red or weak, move the extender closer to the router.

Using a Web Browser:

1. Wi-Fi Connection: Connect your computer or mobile device to the extender’s Wi-Fi network. The default network name (SSID) should be “Rockspace_EXT,” or something similar. No password is required initially.
2. Access Extender Settings: Open a web browser and enter the URL provided in the extender’s manual (commonly something like http://re.rockspace.local or a specific IP address).
3. Setup Wizard: Follow the on-screen instructions. You will need to choose your region, set up an admin password for the extender, and select the Wi-Fi network you wish to extend.
4. Wi-Fi Details: Enter the Wi-Fi password of your existing network when prompted.
5. Finalize Setup: Complete the setup by following any additional on-screen instructions. Once finished, the extender will reboot and apply the settings.

Post-Installation

• Placement: After setting up, place the extender where it can provide the best extending performance. Avoid physical obstructions and interference sources.
• Testing: Check the extended network by connecting devices to the extender’s network and testing the internet connection in areas where coverage was previously weak.
• Adjustments: If necessary, you can log back into the extender’s settings to adjust configurations like SSID, password, or firmware updates.

Tips

• Ensure your router’s firmware is up to date for the best compatibility.
• The extender’s SSID can be different from your router’s to easily distinguish between networks.
• In case of any issues, consult the user manual or Rockspace support for troubleshooting tips.

The post How to setup Rockspace AC2100 Dual-band Wi-Fi Range Extender? appeared first on Re.Rockspace.local.

In today’s digitally connected world, a strong and reliable internet connection is more important than ever. Slow or weak Wi-Fi signals can be frustrating, leading to interrupted video calls, leggy online gaming, and endless buffering during your favorite shows. Fortunately, there’s a solution: the Rock Space Wi-Fi Extender. In this comprehensive guide, we’ll walk you through the setup process step by step, troubleshoot common issues, and answer frequently asked questions to ensure you get the most out of your extender.

The Rock Space WiFi Extender is your ticket to seamless internet connectivity throughout your home. Whether you have dead zones in your living room or a weak signal in the basement, this extender promises to amplify your Wi-Fi signal, providing a stable and speedy internet connection to every corner of your space.

Why Choose the Rock Space Wi-Fi Extender

Before we dive into the setup process, let’s explore why the Rock Space Wi-Fi Extender is an excellent choice for improving your home network.

Enhanced Coverage

With its powerful amplifiers and high-gain antennas, the Rock Space extender extends your Wi-Fi coverage, eliminating dead zones and ensuring a strong signal even in the farthest corners of your home.

Easy Installation

Setting up the Rock Space Wi-Fi Extender is a breeze, thanks to multiple setup methods, including WPS, web browser configuration, and manual setup.

Fast and Stable Connectivity

Enjoy lag-free online gaming, smooth video streaming, and speedy downloads with the Rock Space extender, which boosts your existing Wi-Fi signal to provide a reliable connection.

Getting Started

Now that you’re convinced of the benefits, let’s get started with the setup process.

Unboxing Your Extender

1. Open the Rock Space Wi-Fi Extender package and check for the following items:
   • The extender unit
   • An Ethernet cable
   • A user manual
2. Ensure all components are in good condition.

Choosing the Right Location

The success of your extender largely depends on its placement. Here’s how to choose the ideal spot:

1. Position the extender midway between your Wi-Fi router and the area with weak signal coverage.
2. Keep the extender away from obstructions such as walls and electronic devices that may interfere with the signal.
3. Ensure the extender is within the range of your existing Wi-Fi network.

Setup Methods

The Rock Space WiFi Extender offers three convenient setup methods to suit your preferences.

Using WPS (Wi-Fi Protected Setup)

1. Plug the extender into an electrical outlet within the range of your Wi-Fi router.
2. Press the WPS button on your router and hold it for a few seconds.
3. Within two minutes, press the WPS button on the extender.
4. Once the connection is established, the extender’s LED indicator will turn solid green.

Configuration via Web Browser

1. Connect your computer or mobile device to the Rock Space Extender’s default Wi-Fi network (usually named “Rock Space Extender”).
2. Open a web browser and enter “re.rockspace.local” in the address bar.
3. Follow the on-screen instructions to complete the setup, including selecting your existing Wi-Fi network and entering the Wi-Fi password.
4. Once configured, your extender will restart, and you can connect your devices to the extended network.

Manual Setup with an Ethernet Cable

1. Connect one end of the provided Ethernet cable to your extender and the other end to your computer.
2. Plug the extender into an electrical outlet.
3. Open a web browser and enter “re.rockspace.local” in the address bar.
4. Follow the on-screen instructions to configure the extender manually, including selecting your existing Wi-Fi network and entering the Wi-Fi password.
5. After setup, disconnect the Ethernet cable and connect your devices to the extended network.

Troubleshooting

Even with the straightforward setup process, issues can sometimes arise. Let’s troubleshoot some common problems.

Rockspace Extender Not Powering On

If the extender does not power on:

• Ensure it is plugged into a working electrical outlet.
• Check the power indicator on the extender.
• Try a different outlet if necessary.

Failed Connection to Router

If the extender cannot connect to your router:

• Verify that you followed the setup instructions correctly.
• Ensure your router supports WPS if you are using the WPS setup method.
• Check your Wi-Fi network’s password.

No Internet Access

If you have a connection but no internet access:

• Confirm that your router is online and functioning.
• Check the extender’s LED indicator for any issues.
• Restart both the extender and your router.

Rockspace Extender Not Broadcasting Wi-Fi

If the extender is not broadcasting Wi-Fi:

• Ensure the extender is properly configured.
• Check the Wi-Fi settings in the extender’s web interface.
• Reboot the extender.

FAQ

The Rock Space WiFi Extender is your key to a robust and seamless internet connection throughout your home. Whether you opt for WPS, web browser configuration, or manual setup, you can trust this device to extend your Wi-Fi coverage effectively. Say goodbye to dead zones and hello to uninterrupted connectivity with the Rock Space WiFi Extender Setup.

Boost your Wi-Fi signal today and enjoy a more connected and hassle-free digital experience!

The post Rock Space Wi-Fi Extender: Boosting Your Internet Signal appeared first on Re.Rockspace.local.

Welcome to our comprehensive guide on effortlessly logging in to your Rockspace WiFi router. As proficient experts in networking and router configuration, we understand the significance of providing a seamless user experience when it comes to managing your network settings. In this article, we will provide you with step-by-step instructions to access the login page of your Rockspace WiFi router and make any necessary changes to optimize your network performance.

Before we delve into the login process, there are a few prerequisites you must fulfill:

1. Ensure your computer or mobile device is connected to the Rockspace WiFi network. Locate the WiFi icon on your device and select the appropriate network name (SSID) associated with your Rockspace router.
2. Make sure you have a compatible web browser installed on your device. For the best experience, we recommend using the latest versions of popular browsers such as Google Chrome, Mozilla Firefox, or Microsoft Edge.

Step 1: Find the IP Address of Your Rockspace Router

 To initiate the login process, you need to determine the IP address of your Rockspace WiFi router. The IP address serves as the gateway to access the router’s administration panel. Follow these steps:

1. Open your preferred web browser.
2. In the address bar, type the default IP address used by Rockspace routers. The most common IP addresses are “192.168.1.1” or “re.rockspace.local” Press Enter.
3. If the above-mentioned IP addresses don’t work, you can find the correct IP address by referring to the user manual or checking the manufacturer’s website for your specific Rockspace router model.

Step 2: Access the Router’s Login Page

Now that you have obtained the correct IP address, you can proceed to access the login page of your Rockspace WiFi router. Follow these instructions:

1. In your web browser’s address bar, enter the IP address obtained in the previous step and press Enter.
2. You will be redirected to the login page of your Rockspace router. Here, you need to provide your login credentials to proceed. By default, the username and password are often set to “admin” or mentioned in the user manual. Enter the required information and click the “Login” button.

Step 3: Configure Your Router Settings

Congratulations! You have successfully logged in to your Rockspace WiFi router. Now, let’s explore some essential settings you can configure to optimize your network:

1. Change WiFi Network Name (SSID) and Password To enhance network security and personalize your WiFi network, consider changing the default SSID and password. Follow these steps:

1. Locate the “Wireless” or “WiFi” settings section in the router’s administration panel.
2. Look for the options to change the network name (SSID) and password. Enter your desired values and save the changes.

2. Set Up Guest Network If you frequently have visitors or want to keep your main network separate, setting up a guest network is a useful feature. Here’s how you can do it:

1. Access the “Guest Network” settings section in the router’s administration panel.
2. Enable the guest network and configure the desired network name (SSID) and password.

Also Read- Firmware update of Rockspace Extender

Update Firmware

Regularly updating your router’s firmware is crucial to ensure optimal performance and security. Here’s how you can update the firmware:

1. Visit the official Rockspace website or the manufacturer’s support page.
2. Locate the firmware section and download the latest firmware file for your specific router model.
3. Access the “Firmware Update” or “System Update” settings section in the router’s administration panel.
4. Upload the downloaded firmware file and initiate the update process.

Port Forwarding

If you require specific applications or services to be accessible from the internet, configuring port forwarding can be beneficial. Follow these steps:

1. Access the “Port Forwarding” or “Virtual Server” settings section in the router’s administration panel.
2. Add a new rule by specifying the desired external and internal ports, as well as the IP address of the device you want to forward the ports to.

The post How to Easily Log In to Your Rockspace WIFI Router appeared first on Re.Rockspace.local.

The Rockspace local extender Mesh WiFi system is a powerful and flexible solution for expanding your home Wi-Fi network. With mesh technology, you can create a seamless and strong Wi-Fi network that covers every corner of your home. Here is how to set up your Rockspace local extender Mesh WiFi system:

1. Choose the location for your main router: The main router is the hub of your mesh network and should be placed in a central location in your home with a clear line of sight to other nodes.
2. Connect the main router to your modem: Connect the main router to your modem using an Ethernet cable. Plug the main router into a power source and turn it on.
3. Install the mesh nodes: Place the mesh nodes in other rooms in your home to extend the coverage of your Wi-Fi network. Make sure the nodes have a clear line of sight to the main router or another node. Connect the nodes to power and turn them on.
4. Connect your device to the main router: Connect your device (e.g., smartphone, tablet, or computer) to the main router’s Wi-Fi network.
5. Download the Rockspace app: Download the Rockspace app from the App Store or Google Play Store. Use the app to set up and manage your mesh network.
6. Log in to the app: Log in to the app using your Rockspace account. If you don’t have an account, you can create one from the app.
7. Add the mesh nodes: From the app, follow the steps to add the mesh nodes to your network. The app will guide you through the process of connecting each node to the main router.
8. Customize your network settings: From the app, you can customize your network settings, such as network name and password, and configure other features such as parental controls and guest networks.
9. Test your network: Once you have set up your mesh network, test it to make sure that all nodes are working correctly and that you have good Wi-Fi coverage throughout your home.

By following these steps, you can easily set up your Rockspace local extender Mesh WiFi system and enjoy fast and reliable Wi-Fi coverage in every room of your home.

How to Reset Rockspace local extender Mesh WiFi system?

Resetting your Rockspace local extender Mesh WiFi system is a simple process that can be done in a few steps. Here’s how to reset your Rockspace mesh network:

1. Locate the reset button: The reset button is usually located on the back of each mesh node.
2. Press and hold the reset button: Press and hold the reset button for 10-15 seconds. The LED lights on the node will start flashing, indicating that the reset process has begun.
3. Release the reset button: After 10-15 seconds, release the reset button. The node will restart and return to its default factory settings.
4. Repeat the process for all nodes: Repeat this process for each mesh node in your network.
5. Re-configure the network: After resetting all nodes, you will need to reconfigure the network by following the setup instructions described in the user manual or previous steps.

Note: If you’re resetting your mesh network because you’re having issues with your Wi-Fi, it’s a good idea to restart your modem and main router before reconfiguring the network.

By resetting your Rockspace local extender Mesh WiFi system, you can restore the network to its default settings and resolve any issues you may be experiencing. If you still have trouble with your mesh network after resetting it, you may need to contact Rockspace customer support for additional assistance.

The post How to Setup Rockspace local extender Mesh WiFi System? appeared first on Re.Rockspace.local.

The Rockspace AC1200 is a powerful and flexible Wi-Fi range extender that lets you connect your devices quickly and reliably. With dual-band support for 2.4GHz and 5GHz bands, it can help you boost the coverage and performance of your home Wi-Fi network.

If you’re looking to extend the reach of your Wi-Fi network, the Setup Rockspace AC1200 is an excellent choice. The setup process is simple and straightforward, allowing you to get up and running in no time. Here are the steps to set up your Rockspace AC1200 range extender:

1. Plug in the extender: Connect the Rockspace AC1200 range extender to a power source and turn it on.
2. Connect to the extender’s Wi-Fi network: On a device with Wi-Fi capabilities, such as a smartphone, tablet, or computer, search for and connect to the Rockspace extender’s default Wi-Fi network. The network name (SSID) and password should be provided in the extender’s manual or on a sticker on the extender.
3. Access the extender’s web interface: Open a web browser and enter the extender’s IP address (usually http://192.168.0.254 or re.rockspace.local) into the address bar. This will take you to the extender’s login page.
4. Log in to the extender: Use the default login credentials provided in the manual or on the sticker on the extender to log in to the web interface.
5. Search for available Wi-Fi networks: From the extender’s web interface, go to the Wi-Fi settings page and search for available Wi-Fi networks. Select your main router’s Wi-Fi network from the list and enter the password.
6. Save the changes and reboot the extender: Save the changes you made to the Wi-Fi settings and reboot the extender to apply the new settings.
7. Verify the connection: Check if the extender is working by checking the Wi-Fi signal strength on a device that is connected to the extender’s Wi-Fi network. The device should be able to access the Internet.

With the Setup Rockspace AC1200, you can easily extend the reach of your Wi-Fi network and enjoy fast and reliable connectivity for all your devices. If you encounter any issues, refer to the extender’s user manual or contact Rockspace customer support for assistance.

The post How to Setup Rockspace AC1200 WIFI Extender. appeared first on Re.Rockspace.local.