If http://re.rockspace.local Doesn’t Load

• Try 192.168.0.254 in your browser’s address bar instead.​
• Make sure you’re connected to the Rockspace_EXT network.
• Try with another browser/device or clear your browser cache.

Quick Troubleshooting

• Extender not connecting?
  • Double-check your WiFi password for typos.
  • Place extender closer to the router for setup—then relocate.
• Setup page won’t open?
  • Confirm you’re connected to the extender’s WiFi (not your main network).
  • Use the IP address (192.168.0.254) if the local URL fails.
• Need to reset?
  • Find the reset button on your extender.
  • Press and hold it for 10 seconds. Wait for lights to blink, then retry the setup.

Your Rockspace extender should now be up and running. You can manage settings or change the WiFi password by revisiting the setup page anytime!

The post How to Setup Rockspace Extender Using http://re.rockspace.local appeared first on Re.Rockspace.local.

Install the RS Wi-Fi App– Download the RS Wi-Fi App on your mobile devices by searching for RS Wi-Fi in App store/Google play, or by scanning the QR code. At that point, install the App.

RS Wi-Fi App

Setup the primary mesh mode– The first mode you set up functions as the essential mode, while the rest areas the secondary nodes. If it’s not too much trouble power on one Mesh first connects the other Mesh after you set the first Mesh to the internet on the Apps.

1. Firstly you need to power off your modem and then expel its battery (if there is any).
2. After that use the included Ethernet cable to connect a LAN port of your modem or the Ethernet jack to the (WAN/LAN) port of any node. This node is the primary node.
3. Now Reinstall its battery and power on your modem.
4. Lastly use the included power connector to connect the essential node to a power source, its LED indicator lights will turn green and flicker rapidly.

Hold up about 40 seconds, which demonstrates the system has completed startup. Until the LED indicator flickers green slowly.

Connect the primary node to the internet

• Go to the Wi-Fi network list on your mobile device, select the SSID of the essential node, and enter its password. The SSID and password are determined on the bottom label of any node.
• Run the RS WI-FI App and adhere to the on-screen directions to address the essential node to the web. After the essential node is associated with the web, its LED indicator lights solid green.

Setup the first Rockspace mesh node on App–

1. Run the RS Wi-Fi application. The setup wizard appears. Tap “setup”
2. Consequently recognizes your web association type. Enter data as indicated by the web association type and “Next”. The work unit is associated with the web and the application continues to the following stage.
3. If your Internet association type is PPPoE, Enter your PPPoE user name and password and tap “Next”.

In the event that your web association type is dynamic IP, tap “Next”.

4. Set the wireless network name and password of the mesh unit and tap “OK”.

Note: If you change the wireless network name and password and tap “OK”,   your mobile phone will disconnect with the Rockspace mesh WI-FI network. You have to reconnect to the new wireless network you configured.

5. When the LED of the first mesh unit turns solid green, the mesh unit is associated with the web.

Connect the secondary Rockspace nodes to the internet–

1. Spot each node:

– At a high and open territory.

– Make sure that the wall between any two nodes is less than two.

– Keep your nodes away from electronics with solid obstruction, for example, microwave oven, induction cooker, and refrigerators.

2. Utilize the other power adapters to connectors to associate the remaining secondary nodes to power sources, their LED indicators light solid green. Wait about for 40 seconds. The secondary node is associated with another node when its LED indicator flickers green.

3. Watch the LED indicator of the secondary nodes until their LED indicators light one of the accompanying colors:

Solid green     -    Good Connection
Solid Yellow    -    Fair Connection
Solid Red       -     Disconnectd

4. In the event that a node’s LED pointer does not light solid green, migrate it as indicated by step 1 in V to get it better associated.

To get to the web login

– Wired devices: Connect wired devices to the LAN ports of your nodes.

– Wireless devices: Connect wireless devices to the WI-FI network utilizing the SSID and WI-FI password you set.

On the off chance that you need to manage the network anytime anyplace, tap and utilize your Rockspace account to log in.

The post How to setup Rockspace Mesh WiFi System? appeared first on Re.Rockspace.local.